Cảm biến từ BN 650-10Z
Thông số kỹ thuật cảm biến công tắc từ tính Schmersal BN 650-10Z
đại lý schmersal | đại lý BN 650-10Z
nhà phân phối schmersal | nhà phân phối BN 650-10Z
- With pre-wired cable
- Actuation from side
- with bias magnet
- Non-contact principle
- Long life
- Actuating surface and direction of actuation marked by switch symbol
- Construction form Ø 13 mm
- Thermoplastic enclosure
- Actuating distance up to 60 mm depending on actuating magnet and version
- with central mounting
Dữ liệu đặt hàng
Note (Delivery capacity) |
Not available! |
Mô tả loại sản phẩm |
BN 650-10Z |
Article number (order number) |
101187273 |
EAN (European Article Number) |
4030661335728 |
eCl@ss number, version 11.0 |
27-27-01-05 |
eCl@ss number, version 9.0 |
27-27-01-05 |
ETIM number, version 7.0 |
EC002544 |
ETIM number, version 6.0 |
EC002544 |
Dữ liệu chung
Nguyên tắc làm việc |
Magnetic drive |
Housing construction form |
Cylinder smooth |
Vật liệu thân |
Glass-fibre, reinforced thermoplastic |
Trọng lượng thô |
65 g |
Dữ liệu chung – Features
Suitable for elevators |
Yes |
bias magnet |
Yes |
Số lượng thường mở (NO) |
1 |
Dữ liệu cơ học
Actuating panels |
lateral |
Yếu tố kích hoạt |
Magnet |
Tuổi thọ cơ học, tối thiểu |
1,000,000,000 Operations |
Tốc độ khởi động, tối đa |
18 m/s |
Gắn |
central with threated flange |
Tightening torque of nuts, maximum |
3 Nm |
Dữ liệu cơ học – Switching distances according EN IEC 60947-5-3
Switching distance Sn |
5 mm … 50 mm BP 10 = 5 mm 2 x BP 10 = 17 mm BP 15 = 6 mm 2 x BP 15 = 17 mm 2 x BP 15/2 = 17 mm BP 34 = 15 … 20 mm BP 20 = 20 mm BP 31 = 20 mm BP 11 = 20 mm BP 12 = 10 … 30 mm BP 21 = 25 … 50 mm |
Note (Switching distance Sn) |
Actuating distance up to 50 mm depending on actuating magnet and version. The specified switching distances are applicable for the actuation of individually mounted components without ferromagnetic influence. A change of the distance, either positive or negative, is possible due to ferromagnetic influences. The mutual interference between multiple actuating magnets must be observed. |
Repeat accuracy R |
0.3 mm |
Dữ liệu cơ học – Connection technique
Length of cable |
1 m |
Kết thúc |
Cable |
Wire cross-section |
0.25 mm2 |
Wire cross-section |
23 AWG |
Material of the Cable mantle |
H03VV-F |
Dữ liệu cơ học – Dimensions
Diameter of sensor |
13 mm |
width across flats |
22 BK |
Chiều dài của cảm biến |
103 mm |
Điều kiện môi trường xung quanh
Mức độ bảo vệ |
IP67 |
Nhiệt độ môi trường |
-25 … +75 °C |
Khả năng chống rung |
10 … 55 Hz, amplitude 1 mm |
Khả năng chống sốc |
30 g, on sine wave oscillation |
Resistant to vibration |
30 g, on sine wave oscillation |
Dữ liệu điện
Switching voltage, maximum |
200 VAC |
Switching voltage, maximum |
200 VDC |
Switching current, maximum |
1 A |
Switching capacity, maximum |
30 W |
Switching capacity, maximum |
30 VA |
Phần tử chuyển mạch |
Normally open contact (NO) |
Bounce duration, minimum |
0.3 ms |
Thời lượng thoát, tối đa |
0.2 ms |
Tần số chuyển đổi, tối đa |
300 Hz |
Switching frequency |
1,080,000 /h |
Dữ liệu điện – Digital Output
Design of control elements |
Reed contacts |
Scope of delivery
Scope of delivery |
Actuator must be ordered separately. |
Accessory
Recommendation (actuator) |
BP 10 2x BP 10 BP 15 2x BP 15 2x BP 15/2 BP 34 BP 20 BP 31 BP 11 BP 12 BP 21 |
Recommendation (actuator, lift switchgear) |
BP 10 2 x BP 15/2 2 x BP 15 2 x BP 10 BP 15 BP 34 |